Chemistry Reclaim for Pretreatment Washers: What You Can Reuse and What Limits It
Updated: 2 days ago
Chemistry reclaim on a pretreatment washer means capturing the wash solution after it runs off the part, filtering out the solids and oil it picked up, and sending the water and the active cleaner-coater back to the washer instead of to drain or a hauler. It works when the chemistry is built to run in recycled water and the bath is held in range by titration.
What is chemistry reclaim on a pretreatment washer?
On a spray wand, wash booth or single-step stage washer, the solution that hits the part is water plus cleaner and conversion coating chemistry, usually iron phosphate or zirconium. In a drain-or-haul setup that solution is used once. In a closed loop it drains to containment, runs through filtration and returns to the washer, so the same water and chemistry make many passes.
CPR Systems recycling filters wash water to 20 microns and returns it to the washer, and CPR reports shops cutting water and chemical use by more than 80% against a traditional baseline. Source: CPR Systems wash water recycling.
The idea is not new. Products Finishing described a closed-loop batch cleaning and pretreatment system at a galvanized steel fabricator that recirculated its iron phosphate solution through a bag filter and held the bath in range by titration. Source: Products Finishing, Closed-Loop Cleaning/Pretreatment.
What gets reclaimed, and what doesn't?
Water: reused. Makeup water replaces what leaves on parts and by evaporation.
Cleaner-coater chemistry: the active chemistry returns with the water. You add concentrate to hold titration in range instead of recharging from scratch.
Seal: reclaimed only if the seal is made for it. CPR's optional seal coat is recycle-compatible (CPR Systems wash water recycling).
Soils, oils and solids: not reclaimed. Filtration pulls them out, and they leave the loop as a much smaller waste stream to manage.
No-rinse chemistry keeps the loop simple. CPR's recyclable cleaner-coaters are built to run without a rinse; some shops add one when they run the chemistry stronger than the technical data sheet calls for (CPR Systems wash water recycling).
What limits how long reclaimed chemistry lasts?
Three things set the useful life of a reclaimed bath: the oil and soil load your parts bring in, dissolved salts that filtration cannot remove, and running the chemistry outside its technical data sheet. Titration tells you concentration, not contamination, so a bath can titrate in range and still be loaded.
Watch the parts, not just the numbers. When adhesion, flash rust or coating appearance drift while titration is in range, the bath is due to be drained and recharged. Our guide to pretreatment bath maintenance covers titration, rinse quality and how shops decide when to dump.
How does reclaim compare with an evaporator or hauling?
Hauling: every gallon leaves as regulated industrial wastewater, and you stay exposed to pretreatment permit rules. See EPA rules for powder coating wash water.
Evaporator: boils off the water and leaves a concentrate to dispose of; the chemistry is not reused. See evaporator vs. closed-loop recycling.
Closed-loop reclaim: water and chemistry go back to the washer, and only the removed solids and oils leave. See CPR Systems wash water recycling.
Does reclaim work with iron phosphate and zirconium?
Yes, when the chemistry is designed for recycled water. CPR's PhosBite iron phosphate and Zr Green zirconium both run in recycled water (CPR Systems wash water recycling). Zirconium puts more weight on pH, conductivity and rinse quality than iron phosphate does, so plan your water quality before you switch; see iron phosphate vs. zirconium.
If you supply Caterpillar, the CAT 1E4093 level on the part drawing, High Performance B or Standard Performance C, sets your rinse and seal. See Pretreatment for Caterpillar Suppliers.
How do I find out if reclaim fits my line?
Start with the spec your parts must meet, your part mix and your current chemistry. We clean sample panels free so you can run your own adhesion and salt spray tests, and our savings calculator estimates what closed-loop pretreatment saves on hauling, chemistry and water. When you're ready, request a quote.
Frequently asked questions
Can I add chemistry reclaim to my existing washer?
Often, yes, if it is a hot water washer in good condition. CPR recycling also comes built into our spray wand and single-step stage washer systems (CPR Systems wash water recycling).
Does reclaimed chemistry still need titration?
Yes. Titration is how you hold concentration in range as you add concentrate. It does not show contamination, so watch part results too (pretreatment bath maintenance).
Is reclaimed wash water still regulated?
Any pretreatment wash water you discharge is regulated industrial wastewater. Reclaim cuts how much you discharge or haul; your local sewer authority still sets the rules for what does leave (EPA rules for powder coating wash water). A CPR closed loop system only needs haul when the system goes a clean-out. CPR Systems sets the clean-out plan with you at start-up, based on your production.
Will reclaim change my coating results?
It shouldn't if the bath is held in range, but test it. Tell us the spec or protocol you must meet and send panels; we clean them free so you can run your own tests.




Comments